Fibre Channel, or FC, is a gigabit-speed network technology primarily used for storage networking. Fibre Channel is standardized in the T11 Technical Committee of the InterNational Committee for Information Technology Standards (INCITS), an American National Standards Institute (ANSI)–accredited standards committee. It started use primarily in the supercomputer field, but has become the standard connection type for storage area networks (SAN) in enterprise storage. Despite its name, Fibre Channel signaling can run on both twisted pair copper wire and fiber-optic cables.

Fibre Channel Protocol (FCP) is a transport protocol (similar to TCP used in IP networks) which predominantly transports SCSI commands over Fibre Channel networks.
Fibre Channel started in 1988, with ANSI standard approval in 1994, as a way to simplify the HIPPI system then in use for similar roles. HIPPI used a massive 50-pair cable with bulky connectors, and had limited cable lengths. When Fibre Channel started to compete for the mass storage market its primary competitor was IBM's proprietary Serial Storage Architecture (SSA) interface. Eventually the market chose Fibre Channel over SSA, arguably a better interconnect technology, rather than give IBM control over the next generation of mid to high end storage technology. Fibre Channel was primarily concerned with simplifying the connections and increasing distances, as opposed to increasing speeds. Later, designers added the goals of connecting SCSI disk storage, providing higher speeds and far greater numbers of connected devices.

It also added support for any number of "upper layer" protocols, including SCSI, ATM, and IP, with SCSI being the predominant usage.

Fibre Channel is a layered protocol, with some similarities to the OSI model for networks. It consists of 5 layers, namely:

- FC0 The physical layer, which includes cables, fiber optics, connectors, pinouts etc.
- FC1 The data link layer, which implements the 8b/10b encoding and decoding of signals.
- FC2 The network layer, defined by the FC-PI-2 standard, consists of the core of Fibre Channel, and defines the main protocols.
- FC3 The common services layer, a thin layer that could eventually implement functions like encryption or RAID.
- FC4 The Protocol Mapping layer. Layer in which other protocols, such as SCSI, are encapsulated into an information unit for delivery to FC2.

FC0, FC1, and FC2 are also known as FC-PH, the physical layers of fibre channel.

Fibre Channel routers operate up to FC4 level (i.e. they may operate as SCSI routers), switches up to FC2, and hubs on FC0 only.

Fibre Channel products are available at 1 Gbit/s, 2 Gbit/s, 4 Gbit/s, 8 Gbit/s, 10 Gbit/s and 20 Gbit/s. Products based on the 1, 2, 4 and 8 Gbit/s standards should be interoperable, and backward compatible. The 10 Gbit/s standard (and 20 Gbit/s derivative), however, is not backward compatible with any of the slower speed devices, as it differs considerably on FC1 level (64b/66b encoding instead of 8b/10b encoding). 10Gb and 20Gb Fibre Channel is primarily deployed as a high-speed "stacking" interconnect to link multiple switches.

Fibre Channel switches can be divided into two classes. These classes are not part of the standard, and the classification of every switch is a marketing decision of the manufacturer.

- Enterprise Directors offer a high port-count in a modular (slot-based) chassis with no single point of failure (high availability).

- Departmental Switches are typically smaller, fixed-configuration (sometimes semi-modular), less redundant devices.

A fabric consisting entirely of one vendor is considered to be homogeneous. This is often referred to as operating in its "native mode" and allows the vendor to add proprietary features which may not be compliant with the Fibre Channel standard.

If multiple switch vendors are used within the same fabric it is heterogeneous, the switches may only achieve adjacency if all switches are placed into their interoperability modes. This is called the "open fabric" mode as each vendor's switch may have to disable its proprietary features to comply with the Fibre Channel standard.

Some switch manufacturers offer a variety of interoperability modes above and beyond the "native" and "open fabric" states. These "native interoperability" modes allow switches to operate in the native mode of another vendor and still maintain some of the proprietary behaviors of both. However, running in native interoperability mode may still disable some proprietary features and can produce fabrics of questionable stability.